Yes, it works great on the 17" model as well.Have you tried this on a a1297?
Yes, it works great on the 17" model as well.Have you tried this on a a1297?
Yeah, you'll need to wire the enable lines as follows:I tried it. Unfortunatly i am having white screen issue. Did you do anything different sir with a1297 sir?
[doublepost=1550161971][/doublepost]I tried it. Unfortunatly i am having white screen issue. Did you do anything different sir with a1297 sir?
YES. I fund the permanent solution even if you reset PRAM. The trick is with the hardware id on hex. It took me almost 72 hours but is done and tested. I will share the solution here by tomorrow as to much tired now. I hope you dosdude1 to be agree. First I will wait for your consent.
[doublepost=1542248875][/doublepost]Also can be done a simple jumper to fix the screen brightness by commanding the keyboard brightness with that hardware LVDS permanent jumpers.
You did a Reflow to test a failing GPU? This GPU Series has Problems whit hairline crack between the Core board and the DIE. A Reflow would not solve the problem, well it could shorten some hairline cracks for a short time.
Hmmmmm next time just enter sudo nvram fa4ce28d-b62f-4c99-9cc3-6815686e30f9:gpu-power-prefs=%01%00%00%00 and reboot. This forces the NVRAM to use the integrated GPU instead of the EGPU. This is much faster than a Reflow and less (what is the right English word) destructive. Could be something different is now defective.
Yes, i know. But for testing purpose the NVRAM variable is a quick test. Better that reflowing, at least that is my opinion.
Interposer it is called. Good to know. I just translated it from German.
I see. I have a little other approach. I have harddisk whit Remote Desktop enabled. I just plug the harddisk into the MBP, boot from it and take remotely control over the MBP. Than i perform the NVRAM variable and reboot. Mostly i have screen after this. So i know it is only the GPU.
Hmm but selling those. What do you tell people about the not working TB-Monitor output and the Backlight control?
I may try this modification on the next one. I just bought another defective for the non glare display for mine MBP.
What about resistor r8911?
Does it work with external screen?
[doublepost=1551980867][/doublepost]Hi dosdude1,Yeah, you'll need to wire the enable lines as follows:
- Connect LVDS_IG_BKL_ON to LCD_BKLT_EN
- Connect LVDS_IG_PANEL_PWR to LCD_PWR_EN
- Connect PP3V3_S0 to LCD_BKLT_PWM
hello there...[doublepost=1551980867][/doublepost]Hi dosdude1,
Can you help .I am going crazy with A1286 820-2915.
Did the jumps as per your original post and all worked fine.
The next two done identically ( same model same board ) no backlight.
Tried as per you updates still no backlight.
With or without MuxHat same result.
If there a definitive drawing for the wiring.
All I want is to turn the ........ backlight on !
BTW there is an unbacklit image on the screen
Regards Peter
There is not... I build and sell the modules myself, so at this point, the only way you can get them is to buy them from me.@dosdude1 is there are European distributor for the DyingLight MKII module? I only found one on eBay in Richmond, Virginia, United States.
Hi dosdude1,There is not... I build and sell the modules myself, so at this point, the only way you can get them is to buy them from me.
Check voltages on LCD_BKLT_EN and BKLT_PWM. What do you have there?Hi dosdude1,
Can you help .I am going crazy with A1286 820-2915.
Did the jumps as per your original post and all worked fine.
The next two done identically ( same model same board ) no backlight.
Tried as per you updates still no backlight.
With or without MuxHat same result.
If there a definitive drawing for the wiring.
All I want is to turn the ........ backlight on !
BTW there is an unbacklit image on the screen
Regards Peter